I decided to create a new thread for distributing the manuals that I have collected and scanned. I tend to get busy with work, family, and things around the house and I don't have the time to respond to the manual requests in a timely fashsion. I enjoyed getting the individual requests and hearing about what saws you guys were working on, how you acquired them, what problems you were having, etc. I just feel that everyone's needs will be better served this way. This new thread should work out better.

1. Mcculloch 3200 Chainsaw Repair Manual

No one will have to wait for me to respond to their requests, they can just click on the link and download the PDF. Disclaimer: The following PDF files are from McCulloch literature that I own personally (with one exception noted below) and have been scanned by myself. I know how hard it can be to find good service information on a lot of the older saws and felt like helping everyone out. The 1-XX series shop manual (60270) was provided to me by another site member who is a collector of yellow saws. Deprime said: “ I decided to create a new thread for distributing the manuals that I have collected and scanned. I tend to get busy with work, family, and things around the house and I don't have the time to respond to the manual requests in a timely fashsion. I enjoyed getting the individual requests and hearing about what saws you guys were working on, how you acquired them, what problems you were having, etc.

I just feel that everyone's needs will be better served this way. This new thread should work out better. No one will have to wait for me to respond to their requests, they can just click on the link and download the PDF. Disclaimer: The following PDF files are from McCulloch literature that I own personally (with one exception noted below) and have been scanned by myself.

I know how hard it can be to find good service information on a lot of the older saws and felt like helping everyone out. The 1-XX series shop manual (60270) was provided to me by another site member who is a collector of yellow saws. Brian Thacker said: “ Thanks Ron.

I was looking for torque specs for the cylinder base. Just doing some research. On my 10-10 pro I torqued them to 15 ft. And used lock tight so they did not back off.

I could not find the specs for it so I used a good happy mediocre.I believe the torque spec are listed in the IPL in inch/pounds. Just look up the part number and the spec should be beside it. For example on the PM800: 67 110288 2 Screw - Hx Hd 8-32 x 3/4 (35 - 40 in. Torque) 68 110963 1 Screw - Hx Hd 8-32 x 1 (35 - 40 in. Torque) 69 110644 1 Screw - Hx Hd 8-32 x 1.5 (35-40 in. Torque) 70 62106 4 Screw - 12-24 x 1.75 (70 - 75 in.

Massey Ferguson 135 & 148 Workshop Service Manual For MF135 & 148. Also included as a free extra, is the detailed Perkins 3.152 Engine Manual FYI. Massey Ferguson Silver Mist Gray Massey Ferguson. Perkins AD3-152 Diesel Engine. THROTTLE LINKAGE FOR MF 135 AND MF 150 TRACTORS. Massey ferguson 135 perkins diesel manual.

Storing a chain saw for longer than 30 days requires storage maintenance. Unless the storage instructions are followed, fuel remaining in the carburetor will evaporate, leaving gum-like deposits.

This could lead to difficult starting and result in costly repairs. Never store a chain saw for longer than 30 days without performing the following procedures: Remove the fuel tank cap slowly to release any pressure in tank. Carefullydrain the fuel tank.Start the engine and let it run until the unit stops to remove fuel from carburetor. Allow the engine to cool (approximately 5 minutes). Using a spark plug wrench, remove the spark plug.

Mcculloch 3200 Chainsaw Repair Manual

Pour 1 teaspoon of clean 2-cycle oil into the combustion chamber. Pull starter rope slowly several times to coat internal components.

Replace spark plug. Store the unit in a dry place and away from possible sources of ignition such as a furnace, gas hot water heater, gas dryer,etc. When removing the unit from storage, be sure to perform the following procedures:Remove spark plug.

Pull starter rope briskly to clear excess oil from combustion chamber. Clean and gap spark plug or install a new spark plug with proper gap.Prepare unit for operation.Fill fuel tank with proper fuel/oil mixture. This will help. Thanks, please keep updated. Please do rate the solution positively.thank you for using fixya Dec 15, 2009. You will need a parts breakdown and exploded views to start with as well as a manual, All you have to do is call 1-800-521-8559 and select U.S.

Then select the parts department, have your model number ready and ask them for a PDF of the owners user manual to be emailed to you, they will normally be sent in 1 hour for free. After that is done then you can see the fuel filter and line inside the tank you will need to replace, take your printed views and manual to the nearby lawn mower shop and they will help you get the parts you need even if the original ones are not available. Blow out the carb with chemtool and install the parts, use NEW GAS, NEW OIL and from that day forward never leave fuel in a unit for more than 3 months. Aug 18, 2008.