Husqvarna Designer 1 Service Manual
I presume you have set the machine for free motion quilting in the Menu? There are so many things that could be causing this, and so many variables for tweaking it to optimum performance. What foot are you using? What menu setting?
Have you tried loosening the top thread tension? Bobbin tension? I will keep a lookout for further posts from you with a bit more info that we can start working on. I have a Designer1, not the SE, but have used an Se so will try my best to help. Dec 15, 2010. If you are adjusting the upper tension on your machine and yet there is no difference to the sewing, it seems to me that maybe your upper thread is not in the tension disks correctly. Re-thread taking care to make sure the threads bed down into the tension disks.
I pull off about 2 foot of thread from the spool and put my right-hand finger on the thread very close to the spool (the idea is to hold it down so it doesn't move) then use my left hand to take the thread through the thread run. Once I get close to the needle, I tug the thread a little and you can hear/feel it go into the tension disk. Sometimes it looks like the top thread is the problem, but in fact it is the bobbin which is at fault. Re-insert your bobbin again taking care to click it into its tension slot. If you are still getting bad results, try loosening off the bobbin tension. Use a tiny screwdriver to turn the tension screw (the one just on the outside of the tension slot). Turn it no more than 1/5th of a circle at a time (to the right to tighten, to the left to loosen) then put bobbin back in and test.
You should not need to adjust it more than two or at most three times. If you do, something is seriously wrong with your machine's tensions and it needs to see the Sewing Machine Doctor. May 25, 2010. Designer 1 bobbin case tension adjustment: When the bobbin runs out, sometimes it bends the bobbin case tension spring. Then tension is too light.
Take the bobbin case out of the machine. Tie the loose bobbin thread to the Designer 1 needle plate. Insert the bobbin in the bobbin case. Here’s the tricky part set the bobbin case on the table as if it’s in the machine (Bobbin is visible and sitting horizontal to table top) threaded as if sewing and loose end tied to needle plate (that is removed from the machine). Lift the bobbin case off the table rotate it so that the flat side of the bobbin are vertical to the table and no longer horizontal. Have the bobbin case oriented so that the thread coming out of the bobbin case sprint (slot area where it is put for sewing) is at the top. Lift it high enough that the needle plate is lifted from the table.
Husqvarna Viking Designer 1 Service Manual
Husqvarna Designer 1 Service Manual Download Free
It should not release thread unless you shake it gently and then a very small amount of thread. The needle plate is the exact weight resistance your bobbin case should have on the thread. Oct 28, 2008.
Belt tension, arm/lower shaft belt.7 2. Belt tension, motor belt. Setting the hook in relation to the feeding eccentric (After feeding).8 4. The play of the hook gear. Setting the step motor of the needle.10 6.
Setting the sideway limitation of the sewing head. Setting of the needle in relation to the presser foot. The gap between the needle and the hook.13 9.
Setting the feeding unit sideways.14 10. Setting the stitch plate (the hook cover) in relation to the needle in the feeding direction.15 1 1. The sideways setting of the stitch plate (the hook cover) in relation to the presser foot.15 12a. The height of the hook. The height of the hook, new hook model. The timing of the hook in relation to the needle. The needle height.19 15.
Presser foot parallelism to the feed dog.20 16. School nurse resource manual. Presser foot height to the stitch plate.20 17.
Pivot height.21 18. Threading device.22 19. Pre-setting of the step motor for the feed dog lowering.23 20. Setting the side feeding mechanism sideways.24 21. Feed Dog Lowering.25 22. Feed dog height.26 23.
Stitch length balance basic setting (0-feeding).27 24. Pre-setting the step motor of the feed dog.27 25. Stitch length balance.29 26. Lower thread tension (thread tension of the bobbin case).30 27. Upper thread tensio n - Position 'Sewing'.31 28. Upper thread tension - Position 'Embroide ring'.
Upper thread guard sensor.33 30. Setting the thread take-up spring.34 31. Disconnection when win ding the bobbin.35. Functions of the service menu 'Sensors' - Designer SE. 39 Functions of the service menu 'Sensors' - Designer SE. 40 Functions of the service menu 'Sensors' - Designer SE. 41 Functions of the service menu 'Electronics' - Designer SE.42 Functions of the se rvice menu 'Ele ctronics' - Designer SE.43 Calibration of the touch panel.
43 Functions of the se rvice menu 'Ele ctronics' - Designer SE.44 Enter the Serial number.44 Functions o f the se rvice menu 'Sewing' - Upper th read tensi on.45 Functions of the service menu 'Embroidery' - Upper thread tensio n.46 Functions of the service menu 'E mb Unit' - Hoop sensor adju st.47 New routine for Hoop sensor calibration.48 Update of the memory - Designer SE.50. Upper rear cover.52 Lower rear cover.52 Front cover.53 Parts of the front cover - LCD.54 Parts of the front cover - Tou ch Panel.54 Parts of the front cover - LCD Tra nsformer.55 Parts of the front cover - Bobbin windin g device.55 Parts of the fro nt cover - The thr ead tension complete. 56 DISMANTLING AN D MOUNTING.57 Base Plate.57 Transformer.58 Circuit board - Circuit diagram.59 Stop right / Synchronizer circuit board.60 Sewing head.61 The step motor of the needle.62 The step motor of the presserfoot lifter.63 The hook cover complete step motor housing.64 Parts of the hook cover compl.65 Changing the thread cutter knife.65 The lower thread indicator. 65 The thread cutter step motor.65 Feeding unit.66 Feed teeth.67 The side feeding mechanism complete.68 The side feeding mechanism step motor.69 The feeding unit step motor.70 Hook complete.71. Cover Y-slide.72 Step motor cover.72 Cover upper part.73 Cover lower part.73 Locking switch.73 32. Belt tension, Embroidery unit - X-unit.74 33. Calibration of the end position, Embroidery unit - X-unit.74 34.
Belt tension, Embroidery unit - Y -unit.75 35. Calibration of the end position, Embroidery unit - Y -unit.75 36 The hoop sensor, Embroide ry unit - Y -unit. 76 Step motor, Embroidery unit - Y-un it.77 Step motor, Embroidery unit - X-unit.77 Hoop holder Embroide ry unit - Y- unit.78 Fault.